The BS410 is the base station for the DX410 wireless system, supporting up to 15 registered BP410 beltpacks and/or WH410 all-in-one wireless headsets. The system operates in the 2.4GHz frequency band and features high quality 7kHz wideband audio. The BS410 allows the option for audio bridging by combining 2-wire and 4-wire audio together on A or B channels.
- Two-channels
- 7kHz wideband audio
- 2-wire and 4-wire bridging
- 2-wire auto-nulling
- Lost packet concealment
- Upgraded radio
- Supports up to 15 beltpacks and/or wireless headsets
Audio
- Channels: 2 audio channels
- Capacity: Up to 15 BP410 and/or WH410 per base station
- Full-Duplex: Yes. Single-channel = 4 in simultaneous full-duplex. Dual-channel = 3 in simultaneous full-duplex.
- Radio Frequency Range: 2400 - 2483.5 MHz
- Audio Frequency: 200 Hz - 7kHz
- 4-wire I/O: RJ45, 600 Ohms balanced, level adjustable, simultaneous operation with 2-wire
- 2-wire I/O: XLR-3M, XLR-3F, externally-switchable RTS or Clear-Com, 200 Ohms, level adjustable, null adjustable to 50dB attenuation, typical
- Aux Input: XLR-3F with 1/4" (6.35mm) combo jack, 600 Ohms balanced, level adjustable
- Aux Output: XLR-3M, 600 Ohms balanced, level adjustable
- Headset Connector: 4-pin mini-DIN, Electret microphone
- Headset Output: 200mW into 32 Ohms
- Antenna Type: External 1/2-wave dipole (R-TNC connector), RX/TX horizontal/vertical diversity
- System Distortion: <2%
- Communication Security: 64-bit encryption, dual-slot diversity
Transmitter
- Type: Frequency Hopping, Spread Spectrum (FHSS)
- Transmit Power: 100mW burst
- Modulation Type: Gaussian filtered FSK, TDMA
- Frequency Stability: 13 ppm
- Harmonics/Spurious: Exceeds FCC and ETSI specifications over temperature
Receiver
- Type: Frequency Hopping, Spread Spectrum (FHSS)
- RF Sensitivity:
- Frequency Stability: 13 ppm
- Distortion: <2%
Power Requirements:
- 100 - 240 VAC, 50 - 60 Hz or 12 - 14 VDC
- Environmental:
- Temperature: +32°F - +122°F (0°C - +50°C)
Dimensions
- 1.75 x 19.0 x 17.13 in
- (44 x 483 x 435 mm) (HxWxD)
Weight
- 9 lbs (4.1 kg)
| FCC Consumer Alert This disclosure informs consumers that wireless microphone users must cease any wireless microphone operations in the 600 MHz service band no later than July 13, 2020. In addition, in many instances they may be required to cease use of these devices earlier if their use has the potential to cause harmful interference to 600 MHz service licensees’ wireless operations in the band. Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888-CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC's wireless microphone website. |
