Cost-Effective Expansion For Symetrix Channel I/O
The XIO Stage 4x4 offers a way to affordably increase the channel I/O of your Symetrix DSP units that support Dante. The Stage 4x4 delivers audio over a typical IT network with no audible latency and 4 analog XLR mic/line inputs with phantom power as well as 4 line outputs.
The XIO Stage 4x4 can be configured to remove Symetrix Composer. There is no need for third-party software, outdated DIP switches, or challenging front panel menus. Using Symetrix Composer open architecture software, the four XLR analog inputs and outputs, as well as bus assignments, are each individually configured.
The Symetrix Dante I/O Expanders require Composer for setup and can be used with Symetrix Radius, Prism, and Edge DSPs. Switches, circuit board jumpers, mechanical adjustments, and the need for external software programs are all excluded when using Composer.
Symetrix XIO STAGE 4X4 Features
- Audio input (A/D), output (D/A) expander for Symetrix systems that capitalizes on the surplus DSP of a Dante-enabled Symetrix DSP unit to bring overall system costs down.
- 4 mic/line inputs, including +48 VDC phantom power, and 4 line outputs with the industry leading performance specifications of Radius NX, Edge and Prism DSPs.
- Configured with Symetrix Composer. No third-party software, archaic DIP switches, or complicated front panel menus.
- Network audio expansion using Dante protocol over standard IT networks. Ultralow latency.
- Mounts in standard 8”x8”x4” electrical enclosure.
- Frequency Response: 20 Hz – 20 kHz, ± 0.5 dB.
- Channel Separation: > 110 dB @ 1 kHz, +24 dBu.
- Connectors: Female Neutrik metal body DL series XLR connectors.
- Number of Inputs: Four (4) switchable balanced mic or line level.
- Nominal Input Level: +4 dBu with 20 dB of headroom (digital).
- Maximum Input Level: +23 dBu (1% distortion).
- Mic pre-amp gain: 0, 12, 24, 44 or 54 dB switchable.
- Mic pre-amp EIN: < -125dB with 150 ohm source impedance.
- CMRR: > 76 dB @ 1 kHz, unity gain.
- Input impedance: 8k Ohms balanced, 4k Ohms unbalanced.
- Phantom power (per input): +48 VDC 10 mA maximum.
- Dynamic range: > 116 dB, A-weighted.
- THD + Noise: < -100 dB, unweighted; 1 kHz @ +16 dBu with 0 dB gain.
- ADC Latency: 0.30 mS. ANALOG OUTPUTS
- Frequency Response: 20 Hz – 20 kHz, ± 0.5 dB.
- Channel Separation: > 110 dB @ 1 kHz, +24 dBu.
- Connectors: Male Neutrik metal body DL series XLR connectors.
- Number of outputs: Four (4) balanced line level.
- Nominal output level: +4 dBu with 20 dB of headroom.
- Maximum output level: +24 dBu (+22.8 dBu into a 2k Ohm minimum load).
- Output impedance: 300 Ohms balanced, 150 Ohms unbalanced.
- Dynamic range: > 116 dB, A-weighted.
- THD + Noise: < -94 dB, unweighted; 1 kHz @ +20 dBu with 0 dB gain.
- DAC Latency: 0.60 mS.
- Sampling Rate: 48 kHz.
- Dante Cable: Standard CAT6, maximum device-to-device length = 100 meters.
- Latency: 1.92 mS (input to output, 1mS Dante latency).
- Space Required: Minimum requirement of 8”x8”x4” electrical enclosure.
- Electrical: PoE IEEE 802.3af Class 0, 10 Watts maximum. No line voltage switching required (100-250 VAC, 50-60 Hz).
- Certifications or Compliance: UL 60065, cUL 60065, IEC 60065, FCC 15.109, FCC 15.109(g), FCC 15.107, EN 55032, EN 55103-2, EN 61000-3-3, EN 61000-3-2, ICES-003, RoHS.
Symetrix XIO STAGE 4x4 Downloads
Manual - As of 2/1/2023
Spec Sheet - As of 2/1/2023
Product documents are provided as a courtesy and may not reflect the most up-to-date information. Please contact us for the most up-to-date information.
