Priced individually but only sold in pairs!
Together these technologies provide more consistent and controlled directivity along with improved high frequency response. Improved time-alignment and greater coherence between LF and HF results in a wider sweet spot for enhanced performance both on and off-axis. The re-designed baffle provides a subtle extension to the waveguide effect for additional sonic benefits.
The CMS 503DC uses a 130 mm (5 inch) Dual Concentric driver, featuring treated multi-fibre paper pulp cone and a 20 mm (0.79 inch) PEI dome HF compression driver with Torus Ogive waveguide. Driven by a single powerful magnet, the new CMS 503DC driver offers a true 90 degree conical dispersion pattern across its 70 Hz – 54 kHz (PI Backcan version) response and 89 dB/Watt sensitivity. The driver is capable of handling 120 Watt programme material with 240 Watt peaks for longevity under even the harshest usage conditions.
Notes
- Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
- Unweighted Pink noise input, measured at 1m on axis
- Long term power handling capacity as defined in EIA - 426B test
- Full range ceiling loudspeaker for installation applications
- 60 Watts continuous, 240 Watts peak power
- Next generation 5" Dual Concentric driver featuring Omnimagnet technology
- Torus Ogive waveguide for improved high frequency response and directivity
- Blind Mount version supplied with acoustically enhanced zinc plated steel back can
- Integrated single unit construction for ease of installation
- UL 1480 certified for general signalling systems
- UL 2043 certified for air-handling spaces
- Multiple transformer taps for 70 V and 100 V line systems or 16 Ohm direct input
- Low insertion loss 30 W line transformer with easily accessible tapping switch
- Optimised for LAB GRUPPEN low impedance LUCIA amplifiers with up to 8 CMS series loudspeakers per channel
- Semi matt white finish fits unobtrusively in any environment
- Powder coated UV resistant perforated steel mesh grille with dust protection
- Removable magnetic grille for custom painting
- Optional ARCO designer grilles available for minimal architectural impact
- Self-aligning 3 way clamp mounting system
- Mounting C-ring and ceiling tile rails included
- 5-Year Warranty Program*
- Designed and engineered in the U.K.
- System
- Frequency Response (-3 dB) (1)
- 85 Hz - 50 kHz
- Frequency Range (-10 dB) (1) BM back can model
- 74 Hz - 54 kHz
- Frequency Range (-10dB) (1) PI fitted with back can
- 70 Hz - 54 kHz
- System Sensitivity (1W @1m) (2)
- 89 dB (1 W = 4 V for 16 Ohms)
- Nominal Coverage Angle
- 90 degrees conical
- Frequency Response (-3 dB) (1)
- Power Handling (3)
- Average:
- 60 W
- Programme:
- 120 W
- Peak:
- 240 W
- Average:
- Recommended Amplifier Power
- 120 W @ 16 ohms
- Nominal Impedance (Lo,Z)
- 16 Ohms
- Rated Maximum SPL
- Average:
- 107 dB
- Peak:
- 113 dB
- Average:
- Transformer Taps (via front rotary switch)
- 70 V:
- 30 W (165 O) / 15 W (330 O) / 7.5 W (660 O) / 3.75 W (1320 O) / OFF & low impedance operation
- 100 V:
- 30 W (330 O) / 15 W (660 O) / 7.5 W (1320 O) / OFF & low impedance operation
- 70 V:
- TRANSDUCERS
- Dual Concentric point source driver
- 1 x 130 mm (5.0”) Dual Concentric driver, using Omnimagnet technology
- Low Frequency
- 35 mm (1.38”) voice coil, treated multi fiber paper pulp cone
- High Frequency
- 20 mm (0.79”) PEI dome
- Dual Concentric point source driver
- PHYSICAL
- Enclosure
- Backcan: Zinc plated steel
- Baffle: Reflex loaded UL 94V-0 rated ABS
- Grille: Steel, with weather resistant coating
- Safety Features
- Safety ring located at rear of enclosure for load bearing safety bond
- Clamping Design
- Security toggle clamp
- Blind Mount (BM)
- Complete with fixed backcan
- Pre Install (PI)
- Separate backcan for pre-installation
- Cable Entry Options
- Cable clamp & squeeze connector for conduit up to 22 mm
- Connectors
- Removable locking connector with screw terminals with “loop through” facility
- Conduit Knockouts on PI Backcan
- 3 Sets of horizontal positions 19 / 22 / 28 mm (0.75” / 0.87” / 1.10”)
- Enclosure
- Dimensions
- Bezel diameter
- 205.9 mm (8.11”)
- BM Model: Front of ceiling to rear of backcan
- 188.0 mm (7.40”)
- BM Model: Front of ceiling to top of safety loop
- 205.3 mm (8.08”)
- PI Model: Front of ceiling surface to rear of speaker unit
- 133.3 mm (5.25”)
- PI Model: Front of accessory backcan bezel to top of safety loop
- 153.5 mm (6.04”)
- Hole cutout diameter (all models)
- 190 mm (7.48”)
- Bezel diameter
- Net Weight (ea)
- CMS 503DC BM:
- 4.10 kg (9.04 lbs)
- CMS 503DC PI:
- 3.1 kg (6.83 lbs)
- CMS 503 PI Backcan:
- 2.6 kg (5.73 lbs)
- CMS 503DC BM:
- Packed Quantity
- 2
- Included Accessories
- C Ring
- Tile bridge
- Paint mask
- Cutout template
- Grille
- Optional Accessories
- Plaster (Mud) ring