Priced individually but only sold in pairs!

Together these technologies provide more consistent and controlled directivity along with improved high frequency response. Improved time-alignment and greater coherence between LF and HF results in a wider sweet spot for enhanced performance both on and off-axis. The re-designed baffle provides a subtle extension to the waveguide effect for additional sonic benefits.

The CMS 503DC uses a 130 mm (5 inch) Dual Concentric driver, featuring treated multi-fibre paper pulp cone and a 20 mm (0.79 inch) PEI dome HF compression driver with Torus Ogive waveguide. Driven by a single powerful magnet, the new CMS 503DC driver offers a true 90 degree conical dispersion pattern across its 70 Hz – 54 kHz (PI Backcan version) response and 89 dB/Watt sensitivity. The driver is capable of handling 120 Watt programme material with 240 Watt peaks for longevity under even the harshest usage conditions.

Notes

1. Average over stated Bandwidth. Measured in an IEC baffle in an Anechoic Chamber
2. Unweighted Pink noise input, measured at 1m on axis
3. Long term power handling capacity as defined in EIA - 426B test

• Full range ceiling loudspeaker for installation applications

• 60 Watts continuous, 240 Watts peak power

• Next generation 5" Dual Concentric driver featuring Omnimagnet technology

• Torus Ogive waveguide for improved high frequency response and directivity

• Pre-install version supplied without back can (available separately)

• UL 1480 certified for general signalling systems

• UL 2043 certified for air-handling spaces

• Multiple transformer taps for 70 V and 100 V line systems or 16 Ohm direct input

• Low insertion loss 30 W line transformer with easily accessible tapping switch

• Optimised for LAB GRUPPEN low impedance LUCIA amplifiers with up to 8 CMS series loudspeakers per channel

• Semi matt white finish fits unobtrusively in any environment

• Powder coated UV resistant perforated steel mesh grille with dust protection

• Removable magnetic grille for custom painting

• Optional ARCO designer grilles available for minimal architectural impact

• Self-aligning 3 way clamp mounting system

• Mounting C-ring and ceiling tile rails included

• 5-Year Warranty Program*

• Designed and engineered in England

• System
  • Frequency Response (-3 dB) (1)
    • 85 Hz - 50 kHz
  • Frequency Range (-10 dB) (1) BM back can model
    • 74 Hz - 54 kHz
  • Frequency Range (-10dB) (1) PI fitted with back can
    • 70 Hz - 54 kHz
  • System Sensitivity (1W @1m) (2)
    • 89 dB (1 W = 4 V for 16 Ohms)
  • Nominal Coverage Angle
    • 90 degrees conical

• Power Handling (3)
  • Average:
    • 60 W
  • Programme:
    • 120 W
  • Peak:
    • 240 W

• Recommended Amplifier Power
  • 120 W @ 16 ohms

• Nominal Impedance (Lo,Z)
  • 16 Ohms

• Rated Maximum SPL
  • Average:
    • 107 dB
  • Peak:
    • 113 dB

• Transformer Taps (via front rotary switch)
  • 70 V:
    • 30 W (165 O) / 15 W (330 O) / 7.5 W (660 O) / 3.75 W (1320 O) / OFF & low impedance operation
  • 100 V:
    • 30 W (330 O) / 15 W (660 O) / 7.5 W (1320 O) / OFF & low impedance operation

• TRANSDUCERS
  
  • Dual Concentric point source driver
    • 1 x 130 mm (5.0”) Dual Concentric driver, using Omnimagnet technology
  • Low Frequency
    • 35 mm (1.38”) voice coil, treated multi fiber paper pulp cone
  • High Frequency
    • 20 mm (0.79”) PEI dome

• PHYSICAL
  
  • Enclosure
    • Backcan: Zinc plated steel
    • Baffle: Reflex loaded UL 94V-0 rated ABS
    • Grille: Steel, with weather resistant coating
  • Safety Features
    • Safety ring located at rear of enclosure for load bearing safety bond
  • Clamping Design
    • Security toggle clamp
  • Blind Mount (BM)
    • Complete with fixed backcan
  • Pre Install (PI)
    • Separate backcan for pre-installation
  • Cable Entry Options
    • Cable clamp & squeeze connector for conduit up to 22 mm
  • Connectors
    • Removable locking connector with screw terminals with “loop through” facility
  • Conduit Knockouts on PI Backcan
    • 3 Sets of horizontal positions 19 / 22 / 28 mm (0.75” / 0.87” / 1.10”)

• Dimensions 
  • Bezel diameter
    • 205.9 mm (8.11”)
  • BM Model: Front of ceiling to rear of backcan
    • 188.0 mm (7.40”)
  • BM Model: Front of ceiling to top of safety loop
    • 205.3 mm (8.08”)
  • PI Model: Front of ceiling surface to rear of speaker unit
    • 133.3 mm (5.25”)
  • PI Model: Front of accessory backcan bezel to top of safety loop
    • 153.5 mm (6.04”)
  • Hole cutout diameter (all models)
    • 190 mm (7.48”)

• Net Weight (ea)
  • CMS 503DC BM:
    • 4.10 kg (9.04 lbs)
  • CMS 503DC PI:
    • 3.1 kg (6.83 lbs)
  • CMS 503 PI Backcan:
    • 2.6 kg (5.73 lbs)

• Packed Quantity
  • 2

• Included Accessories
  • C Ring
  • Tile bridge
  • Paint mask
  • Cutout template
  • Grille

• Optional Accessories
  • Plaster (Mud) ring